Panasonic KXTGL430 Istruzioni per gli Interventi

Operating InstructionsCordless Telephone with Digital Answering MachineModel No.KX-TGL430KX-TGL432KX-TGL433KX-TG3683Model shown is KX-TGL430.Before in

Battery chargingCharge for about 7 hours.R Confirm “Charging” is displayed (1).R When the batteries are fully charged,“Fully charged” is displayed.1No

ControlsHandsetBAAA CBDFEDFEHIJGShoulder gripSpeakerMjN/MkN (VOL.: Volume up/down)M /ZN (TALK/Speakerphone)Dial keypad (*: TONE)MicrophoneReceiverDisp

Display iconsHandset display itemsItem MeaningWithin base unit rangeOut of base unit rangeThe line is in use.R When flashing:The call is put on hold.R

Recording your greetingmessageYou can record your own greeting messageinstead of using a pre-recorded greetingmessage. See page 35 for details.1 MMENU

Making calls1 Lift the handset and then dial the phonenumber.R To correct a digit, press MCLEARN.2 Press M/ZN to make the call.R To make the call usin

Erasing all numbers in the rediallist1 MEN (Redial/CID)R If the caller list is displayed, press MEN(Redial/CID) again to switch to theredial list.2 MM

receive a call while on the phone, you will heara call waiting tone.If you subscribe to both Caller ID and CallWaiting with Caller ID services, the 2n

4 Wait for the paged party to answer.R If the paged party does not answer,press MBACKN to return to the outsidecall.5 To complete the transfer:Press M

Call blockYou can press the MCN (Call Block) key in thefollowing situations to disconnect the currentcall and add a phone number to the call blocklist

4 Enter the phone number (24 digits max.).a MSAVEN a MOFFNStoring a range of number1 MCN (Call Block)2 MbN: “Block range of numbers” aMSELECTN3 MMENUN

IntroductionModel composition ...3Accessory information ...3Important InformationFo

PhonebookYou can add 100 names (16 characters max.)and phone numbers (24 digits max.) to thephonebook, and assign each phonebook entryto the desired g

calling (ringer ID), if you have subscribed toCaller ID service.Changing group names/setting ringerIDThe default group name is “Group 1” to“Group 9”.1

Speed dialYou can assign 1 phone number to each ofthe dial keys (1 to 9) on the handset.Adding phone numbers to speeddial keysn By entering phone numb

Menu listTo access the features, there are 2 methods.n Scrolling through the display menus1 MMENUN2 Press MCN or MDN to select the desired main menu.

Sub-menu 1 Sub-menu 2 Settings CodeNew messagealert*1Outgoing call– On/OffOn<Off>#338 37Outgoing call– Notification to–Outgoing call– Remote cod

Main menu: “Speed dial”Operation CodeViewing the speed dial entry. #261 22Main menu: “Settings”Sub-menu 1 Sub-menu 2 Settings CodeRing adjustments

Sub-menu 1 Sub-menu 2 Settings CodeKey detectorsetting*6– 1:Add newdevice (forDetector1)*7– 2:Add newdevice (forDetector2)– 3:Add newdevice (forDetect

Sub-menu 1 Sub-menu 2 Settings CodeCaller ID edit(Caller ID number autoedit)– <On> Off#214 34Auto talk*9– On <Off>#200 15Set tel lineSet d

Main menu: “Key detector”*6Sub-menu 1 Sub-menu 2 Settings CodeSearch– – #655 –Battery check– –*1 If you program these settings using one of the unit

AlarmAn alarm sounds at the set time for 1 minuteand is repeated 5 times at 5 minute intervals(snooze function). A text memo can also bedisplayed for

Model compositionSeries Model No.Base unit HandsetPart No. Part No. QuantityKX-TGL430seriesKX-TGL430 KX-TGL430 KX-TGLA40 1KX-TGL432 KX-TGL430 KX-TGLA4

2 MbN: Select the desired setting. aMSAVENR If you select “Off”, press MOFFN toexit.3 Enter the desired hour and minute youwish to start this feature.

n From the phonebook:1 MMENUN#2682 MbN: “On” a MSELECTN3 MbN: Select “Outgoing call” tomonitor from outside. a MADDN4 MbN: “Phonebook” a MSELECTN5 MbN

If you want to respond from your monitoringphone, press #1 using tone dialing.You can turn off the baby monitor featureby pressing #0.Note:R The unit

Using Caller ID serviceImportant:R This unit is Caller ID compatible. To useCaller ID features, you must subscribe to aCaller ID service. Contact your

Note:R If the entry has already been viewed oranswered, “” is displayed.Editing a caller’s phone numberYou can edit a phone number in the caller listb

Answering systemThe answering system can answer and recordcalls for you when you are unavailable toanswer the phone.You can also set the unit to play

1 MMENUN#3042 MYESN a MOFFNPlaying back the greetingmessage1 MMENUN#3032 To exit, press MOFFN.Listening to messagesImportant:R When using the base uni

Key Operation*6 Reset to a pre-recordedgreeting message*1 If pressed within the first 5 seconds of amessage, the previous message isplayed.*2 To resum

Turning on/off the new message alertsetting1 MMENUN#3382 MbN: “On/Off” a MSELECTN3 MbN: Select the desired setting. aMSAVEN a MOFFNEditing the set pho

2 Enter the desired 3-digit remote accesscode. a MSAVEN a MOFFNDeactivating remote operationPress * in step 2 on “Remote access code”,page 38.R The en

Additional/replacement accessoriesPlease contact your nearest Panasonic dealer for sales information (page 59).Accessory item Model number/Specificati

1 MMENUN#3102 MbN: Select the desired setting. aMSAVEN a MOFFNNumber of rings before the unitanswers a callYou can change the number of times thephone

Voicemail serviceIn addition to your unit’s answering systemyou may also have voicemail service fromyour phone service provider. Voicemail isan answer

2 Follow the pre-recorded instructions.3 When finished, hang up.Note:R You can also use the MACCESSN soft key,if displayed, to play new voicemailmessa

4 Adjust the adaptor to hold the base unit,then push it in the direction of the arrowuntil it clicks into place.5 Mount the unit on a wall then slide

To remove the wall mounting adaptorWhile pushing down the release levers (A),remove the adaptor (B).BAAChargerDrive the screws (1) (not supplied) into

Error messagesDisplay message Cause/solutionAsk phonecompany forVM access #R You have not stored the voicemail access number. Store thenumber (page 41

TroubleshootingIf you still have difficulties after following the instructions in this section, disconnect the base unit’sAC adaptor, then reconnect t

Problem Cause/solutionI fully charged the batteries, but– still flashes,– is displayed, or– the operating time seems tobe shorter.R Clean the battery

Caller ID/Talking Caller IDProblem Cause/solutionCaller information is notdisplayed.R You must subscribe to Caller ID service. Contact yourphone servi

Answering systemProblem Cause/solutionThe unit does not record newmessages.R The answering system is turned off. Turn it on (page 35).R The message me

For your safetyTo prevent severe injury and loss of life/property, read this section carefully beforeusing the product to ensure proper and safeoperat

Liquid damageProblem Cause/solutionLiquid or other form of moisturehas entered the handset/baseunit.R Disconnect the AC adaptor and telephone line cor

FCC and other informationThis equipment complies with Part 68 of the FCC rules and the requirements adopted by the ACTA. On the bottom of this equipme

manufacturer about the availability of Hearing Aids which provide adequate shielding to RF energy commonly emitted by digital devices.WHEN PROGRAMMING

Compliance with TIA-1083 standard: Telephone handsets identified with this logo have reduced noise and interference when used with T-Coil equipped hea

Guía Rápida EspañolaConexionesUnidad base1 Conecte el adaptador de corriente alterna a la unidad presionándolo firmemente.2 Enganche el cable para fij

Instalación y carga de la bateríaCargue aproximadamente durante 7 horas.Nota:LUTILICE SOLO baterías recargables de Ni-MH tamaño AAA (R03) ( ).LNO util

Cambio de idiomas (Auricular) (predeterminado: “English”)Cuando instale las baterías por primera vez, es posible que aparezca “Set date/time Press SEL

Directorio telefónico (Auricular)Para añadir entradas1{<} k s {MENU}2{r}: “Agregar Ent. Nueva” s {SELEC.}3Introduzca el nombre de la persona (máx.

¿Es posible añadir otro auricular accesorio a mi unidad base?LSí, puede añadir hasta 6 auriculares (incluyendo los que se venden con su unidad base) a

Customer servicesAccessories!hp://shop.panasonic.com/supportCustomer Services DirectoryShopfor all your Panasonic gearGo to Get everything you need t

R This product is unable to make calls when:– the handset batteries need recharging orhave failed.– there is a power failure.BatteryR We recommend usi

Limited Warranty (ONLY FOR U.S.A.)Limited Warranty Coverage (For USA Only)LaborOne (1) YearPartsOne (1) YearTo submit a new repair request and for qui

Limited Warranty Limits and Exclusions(As examples, this excludes damages for lost time, travel to and from the servicer, loss of or damage to media o

Index# 3-way conference: 16A Additional handset: 32Alarm: 29Answering calls: 15Answering systemCall screening: 39Erasing messages: 36, 37, 39Gre

63NotesTGL43x(en)_1117_ver041.pdf 63 2015/11/17 16:08:05

1 Reconnect AC adaptor to the base unit.2 Check if telephone line cord is connected.3 Use rechargeable Ni-MH batteries. (Alkaline/Manganese/Ni-Cd

R If the reception for a base unit location isnot satisfactory, move the base unit toanother location for better reception.EnvironmentR Keep the produ

SpecificationsR Standard:DECT 6.0 (Digital Enhanced CordlessTelecommunications 6.0)R Frequency range:1.92 GHz to 1.93 GHzR RF transmission power:115 m

Setting upConnectionsn Base unitConnect the AC adaptor to the unit bypressing the plug firmly.Fasten the cord by hooking it.Connect the AC adaptor to