INSTALLATION INSTRUCTIONSCS-MKE7NKUCS-MKE9NKUCS-MKE12NKUCS-MKE18NKUCS-MKE24NKUAPPENDIX C(852-6-4190-583-00-0)A-3
93-4. Removing and Installing the Grille3-4-1. Indoor unit types (CS-MKE7NKU, CS-MKE9NKU, CS-MKE12NKU)Basically, these models can be installed and wi
103-4-2. Indoor unit types (CS-MKE18NKU, CS-MKE24NKU)Basically, these models can be installed and wired with-out removing the grille. If access to any
113-5. Shape the Indoor Side Tubing(1) Arrangement of tubing by directionsa) Right or left tubingCut out the corner of the right/left frame with ahac
123-7. Wiring Instructions for Inter-unit Connections(1) Insert the inter-unit wiring (according to local codes)into the through-the-wall PVC pipe. R
13When connecting each power wire to the correspondingterminal, follow the instructions “How to connect wiringto the terminal” and fasten the wire sec
143-8. Mounting(1) To install the indoor unit, mount the indoor unit ontothe 2 tabs on the upper part of the rear plate. (2) Hold down the air discha
15Hole in wallBent partNarrow tubeWide tubeRear panelFig. 38Drain capDrain hoseFig. 39 Left-side tubing /HDGWKHWXELQJDQGGUDLQKRVHWKURXJKWKH
SlantDrainhoseIndoorunitCondensationInsulation material/RFDOO\SXUFKDVHGmust be used.16To unmount indoor unitPress the 2 marks on the lower part of
174. How to Test Run the Air ConditionerAfter turning on the power of the air conditioner, use theremote controller and follow the steps below to cond
185. Remote Controller Installation PositionThe remote controller can be operated from either anon-fixed position or a wall-mounted position.To ensur
For Indoor UnitThis air conditioner uses the refrigerant R410A. External diameter of service port R410A: 5/16" Split System Air Conditioner 85264
196. Address Switch6-1. Address Setting of the Remote ControllerThe address can be set in order to prevent interferencebetween remote controllers wh
207. Connecting a Home Automation DeviceThe HA (white) 4P terminal is located on the indoor unit PCB. If a HA device willbe used, connect it to this
DC1111-0
2IMPORTANT! Please Read Before StartingThis air conditioning system meets strict safety and operatingstandards. As the installer or service person, it
3 $SSO\UHIULJHUDQWOXEULFDQWWRWKHPDWFKLQJVXUIDFHVRIthe flare and union tubes before connecting them, thentighten the nut with a torque wrench f
41. GeneralThis booklet briefly outlines where and how to install theair conditioning system. Please read over the entire setof instructions for the
51-5. Additional Materials Required for Installation1. Refrigeration (armored) tape2. Insulated staples or clamps for connecting wire(See local codes
6 install the indoor unit more than 3.3' (1 m) away from anyantenna or power lines or connecting wires used for tele-vision, radio, telephone, s
7Set screw only for transportationFig. 6Rear panelmarksFig. 7Left tubingRighttubingRight-reartubing(recommended)Right-downwardtubingLeft-reartubingLef
8IndoorsideOutdoorsideHole should be made at a slight downward slant to theoutdoor side.NOTEFig. 10Plastic coverINSIDE OUTSIDEWallSlightanglePVC pipe
Commenti su questo manuale